Procomm Plus Configuration Settings

The following information is the configuration settings for the Procomm Plus 32 version of software to communicate with the CSR and Prizm family of Commercial Inserters using Windows NT 4.0 and Windows 95/98.

Follow the instructions on the installation process from the Procomm Plus User's Manual. Use the Standard installation option. The information listed below are the configuration settings after the installation of Procomm Plus 32.

Note: Verify that the modem has been installed on the PC computer before configuring Procomm Plus 32.

To run Procomm Plus 32, select the <Start> tab from the Windows Display, click <Programsick <Programs>, <Procomm Plus>, and then <Procomm Plus>. Then go to the Menu. Select the following and edit if necessary .

OPTIONS Tab

Systems Option
 
Modem Connection for the CSR: Select Add New Modem/Connection (select your modem)
                                                        Select Modem Connection Properties: (set the following)
                         bsp;                                 Baud rate: (baud rate of CSR), Parity Bit = ODD, 
                                                        Data Bits =7, Stop Bit =1 and Hardware Flow Control. 
                                                        Select "Make this connection available to Procomm Plus"
Modem Connection for the Prizm: Select Add New Modem/Connection (select your modem)
                          &nbbsp;                                Select Modem Connection Properties: (set the following)
                                                         Baud rate: (baud rate of Prizm), Parity Bit = None, 
                                                         Data Bits =8, Stop Bit =1 and Software Flow Control. 
                                                         Select "Make this connection ection available to Procomm Plus"
Dialing Options: Set your choice on dialing in attempts.
                            Select Dialing Properties: Edit your location where you will dial from.
System Options: (Leave as is)

Data Option
 
General: Current Data Options: Normal Options. (Leave as is, no changes required)
Advanced: Current Data Options: Normal Options. Verify (Full Duplex). (Leave as is)
Left Mouse: (Leave as is)
Right Mouse: (Leave as is)
Paths: (Leave as is)
Setup Files: (Leave as is)
Transfer Protocol: ASCII (Leave the rest of the information as is)
Terminal Options: Select TVI910 (Leave the rest of the information as is)
Terminal Fonts: (Leave as is)
Terminal Colors: (Leave as is)
Windows Colors: (Leave as is)

Keyboard Editor

Verify that TVI910.kbd is selected. If not, OPEN it. Click the darkened lettered keys to edit their function.

Click F1. Verify the following, and edit information if needed.
 
Normal Send Text Leave as is
Shift Send Text ^A'^M
Ctrl Send Text ^\1
Shift-Ctrl Send Text ^\D
Alt-Shift Send Text ^AL^M
Entry Options   Character

Click F2. Verify the following, and edit information if needed.
 
Normal Send Text Send Text Leave as is
Shift Send Text ^AM^M
Ctrl Send Text ^\2
Shift-Ctrl Send Text ^\E
Alt-Shift Send Text
Entry Options   Character

Click F3. Verify the following, and edit information if needed.
 
Normal Send Text Leave as is
Shift Send Text ^AN^M
Ctrl Send Text ^\3
Shift-Ctrl Send Text ^\F
Alt-S Alt-Shift Send Text ^\15
Entry Options   Character

Click F4. Verify the following, and edit information if needed .
 
Normal Send Text Leave as is
Shift Send Text ^AO^M
Ctrl Send Text ^\4
Shift-Ctrl Shift-Ctrl Send Text  
Alt-Shift Send Text
Entry Options   Character

Click F5. Verify the following, and edit information if needed.
 
Normal Send Text Leave as is
Shift Send Text
Ctrl Send Text ^\5^\5
Shift-Ctrl Send Text  
Alt-Shift Send Text  
Entry Options Character

Click F6. Verify the following, and edit information if needed .
 
Normal Send Text Leave as is
Shift Send Text
Ctrl Send Text ^\6
Shift-Ctrl Send Text  
Alt-Shift Send Text  
Entry Options   Character

Click F7. Verify the following, and edit information if needed.
 
Normal Send Text Leave as is
Shift Shift Send Text ^Af^M
Ctrl Send Text ^\7
Shift-Ctrl Send Text Leave as is
Alt-Shift Send Text  
Entry Options   Character

Click F8. Verify the following, and edit information if needed.
 
Normal Send Send Text Leave as is
Shift Send Text ^Ag^M
Ctrl Send Text ^\8
Shift-Ctrl Send Text Leave as is
Alt-Shift Send Text  
Entry Options Character

Click F9. Verify the following, aClick F9. Verify the following, and edit information if needed .
  T="20">Entry Options
Normal Send Text Leave as is
Shift Send Text ^Ah^M
Ctrl Send Text ^\9
Shift-Ctrl Send Text Leave as is
Alt-Shift Send Text Leave as is
Entry Options Character

Click F10. Verify the following, and edit information if needed .
 
Normal Send Text Leave as is
Shift Send Text ^Ai^M
Ctrl Send Text ^\10
Shift-Ctrl Send Text ^\A
Alt-Shift Send > Send Text Leave as is
Entry Options   Character

Click F11. Verify the following, and edit information if needed.
 
Normal Send Text Leave as is
Shift Send Text ^Aj^M
Ctrl Send Text ^\11
Shift-Ctrl Send Text Send Text ^\B
Alt-Shift Send Text  
Entry Options Character

Click F12. Verify the following, and edit information if needed.
 
Normal Send Text ^AK^M
Shift Send Text  
Ctrl Send Text ^\ ^\12
Shift-Ctrl Send Text ^\C
Alt-Shift Send Text  
Entry Options   Character

All other darkened lettered keys (Non Function keys) in the Keyboard Editor does not need to be edited.

Configuring a telephone book for the CSR/Prizm

1)  From the Main Menu of Procomm Plus open the FILE menu.
2)  Select "Connection Directory". In this menu click FILE and select NEW.
3)  Click the "New Entry" icon (looks like an open book) and edit your information.
4)  Select and verify the following :

Data Connection "Add your modem here"
Terminal TVI910
Protocol ASCII
Steps to begin communicating with the CSR/Prizm

   1)  Labeled on the keyboard are function keys F1 through F12. Each CSR/Prizm has an ID number/letter: 1-9 or A-F . Thebasic configurations on most CSR/Prizm systems use the numbering system .
   2)  If your CSR/Pt>2)  If your CSR/Prizm is labeled with ID "1", then to log on to it. You will need to press and hold the
         <CTRL> key down and press the <F1> key to log on .

    F1 = ID "1" F2 = ID "2" F3 = ID "3" F4 = ID "4" F5 = ID "5"

    F6 = ID "6" F7 = ID "7" F8 = ID "8" F9 = ID "9"

    If your CSR/Prizm has an ID of a letter (A, B, C, etc.), then you will need to press and hold <SHIFT> and <CTRL> then press the following keys .

    F10 = ID "A" F11 = ID "B" F12 = ID "C" F1 = ID "D"


    To log off properly press and hold the <CTRL> key and press an unused ID key. For example, <CTRL> F12.
    • The following information is specific for the CSR, not the Prizm. Refer to the Prizm User's Manual for operation. Note: After successful log on, the main menu (the Status Menu which is the display that you see upon logging on) of the CSR can control each VCR Deck by the use of the following key combination:
      • combination:


    This is only for the CSR and is not applicable to the Prizm.
     
    VCR Deck A <SHIFT> + F1    (F13)
    VCR Deck B <SHIFT> + F2    (F14)
    VCR Deck C <SHIFT> + F3    (F15)
    VCR Deck D <SHIFT> + F4    (F16)

    After logging on, press the <S> key to go into the SYSTEM SETUP MODE. This will allow you to configure your CSR. When you are in this menu some key combinations will be required.

    While in the SETUP MENU, F1- F12 keys can be selecteNU, F1- F12 keys can be selected by just by pressing the key by itself. However, to use the F13, F14, F15 and F16 keys choose the selected key combination below :
     
    F13 <SHIFT> + F1
    F14 <SHIFT> + F2
    F15 <SHIFT> + F3

    Warning: Do not select F16 from this menu if your CSR is a model 191/192. Doing so will erase your memory and all of the configuration settings and data from your CSR.
     
     F16   <SHIFT> + F4

    If you need information on configuring your system please refer to the User's manual of your particular CSR unit.

    If you

    If you need information on configuring your Prizm system please refer to the Prizm User' Manual.

     

che>